DEFINITION OF DEFECTS
疵点定义
Any deficient area of fabric, assembly, pressing, cutting and / or construction of a garment that adversely affects the
appearance, wearability or serviceability. Defects can occur in the following area:
任何布的缺点范围,组合,熨,裁或组织感到成衣上的外观穿着或服饰上,缺点范围包括
1) Fabric
( 布
)
2) Cutting
(裁)
3) Assembly
(
组合
)
4) Washing
(
洗水)
5) Pressing
(
整熨
)
6) Final
Packing
(
最后包装材料)
7) Rescreen
(
包装底面加纸隔板)
8)
1) IN-LINE
GARMENT
INSPECTION
( 中期成衣检查
)
1.1 –
Purpose
of
In-Line
Inspection(
中期检查目标
)
a) The purpose of inspection while work is in process is to identify and resolve issues in garment manufacture
before they result in garment rejects, when the whole garment has finished production,.
检查目标进行时,厂方要知道检查报告上的不接受程度
,在生产未完成之前就要解决问题。
It is important at this stage for quality inspectors to work with the factory supervisors and operators in order to
insure quality from the beginning of the manufacturing process. Let’s get it right the first time!
这是对检查员和厂方负责人进行的质量控制,让我们第一时间去做。
b) The Degas Quality Inspector must document all discrepancies on the Inspection Report, and review the
Inspection Report with the Factory Manager as well as the Reflex Quality Control Supervisor and
Merchandiser Manager.
检查员必须查阅文件上的细节和检查上的缺点,要和厂方改善质量和报告给验货主管及跟单经理。
c) The Factory Manager should receive a copy of the Inspection Report and should sign a copy acknowledging its
receipt.
厂方负责人一定要有一份检查报告副本和有厂方签署。
d) Copies of all Inspection Reports must be filed in the Quality Control Inspection folder for the Reflex
Production Order.
合同上一定要有一份检查副本和质量控制也要存一份检查报告。
All discrepancies discovered during In-Line Inspection must be repaired and must be reviewed again during
Final Inspection.
所有中期检查后的缺点一定要在末期检查之前修改好。
1.2 –
Fabric
Inspection
at
Manufacturing
Factory
( 在厂方检查布料
)
a) When fabric is delivered to the Factory that will be Manufacturing Degas garments, it must be inspected by the
Factory’s Staff using the Four Point System.
当布料送到工厂预备做货时,厂方人员要跟上述的四个要点检查。
b) Degas will not conduct fabric inspection unless requested to do so by the Manufacturing Factory. The Reflex
Quality Inspector should, however, audit the factory’s quality control procedures.
除非有必要,否则不会引进布料到工厂,公司检查员只有跟厂方的进行程度。
1.3 –
Sample
Size
Guidelines
for
In-Line
Inspection
(
中期检查目标数量)
If all sizes and colours are not available at the time of In-Line Inspection, then as many sizes and colour as
possible should be inspected.
如果在中期检查时,只有部分的颜色和数量,则尽可能地多查一些尺寸和数量。
The quantity inspected by size and colour should be noted on the Inspection Report.
检查的数量和颜色必然要记录在报告上。
2